-
product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm
40-294-013
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Resistor Card 2-Channel 2 Ohm to 32.7k Ohm With SPDT
50-293-132
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Torque Gauges
Mark-10 torque gauges and torque testers are accurate and feature-rich torque measurement products ideal for a wide range of torque applications. All torque gauges and torque testers capture the peak torque in both directions (CW and CCW) and have selectable units of torque measurement. Torque capacities are available from 10 ozFin full scale to 5,000 lbFin, depending on the torque gauge or torque tester. Units may be handheld or used with a test stand and gripping fixtures to create a complete torque testing solution. All torque gauges and torque testers carry the CE mark.
-
product
PXIe-1071, 4-Slot, Up to 3 GB/s PXI Chassis
781368-01
PXIe, 4-Slot, Up to 3 GB/s PXI Chassis—The PXIe‑1071 is designed for a wide range of test and measurement applications and provides a high-bandwidth backplane. Its compact and lightweight form factor is ideal for minimizing the footprint of your installation, making it ideal for desktop or portable use cases. The PXIe‑1071 accepts PXI Express modules or standard PXI hybrid-compatible modules in every peripheral slot.
-
product
PXI Dual 18 Channel MUX, 96-Pin SCSI Connector
40-735-912-S1
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the d...show more -
product
LED Test
Universal LightProbe Penta sensors are Optomistic Products' most popular LED test sensor, relied upon for their versatility in accommodating most LED test applications for color and intensity. The Penta Sensor provides analog voltage outputs, and features built-in color binning, eliminating the need to convert LED wavelength to visual color in the ATE software, and saving valuable processing time. For use with any of the Universal LightProbe Fiber-Optic Probes.
-
product
Clock Generation Devices
Analog Devices offers ultralow jitter clock generation products for wireless infrastructure, instrumentation, broadband, automatic test equipment, and other applications demanding subpicosecond performance. Our clock products are ideal for generating the high speed, low noise clock signals required to clock high performance analog-to-digital converters (ADCs) and digital-to-analog converters (DACs). ADI clock ICs integrate PLL cores, dividers, phase offset, skew adjust, and clock drivers in small chip scale packages.
-
product
Developers' Toolkits
If you are a hardware developer, using RapidDriver Explorer with just a couple of clicks, you can easily start testing and debugging your USB, ISA, PCI or Parallel Port device. You do not have to perform any additional steps - everything is already done!If you are a software developer, you can write your own application with the help of RapidDriver Developer, TVicHW32 or TVicPort without writing a device driver and being a DDK expert - we have already built-in generic device drivers for you! Our...show more -
product
PCI High Density Pecision Resistor Card, 9-Channel, 2Ω To 31.5Ω
50-298-110
The 50-298-110 is a high density programmable resistor card with 9 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Channel Replicator
Series 7000
The Series 7000 System is a multi-radio test network which replicates the propagation path of real-world applications. With complete bi-directional capability radios may operate in full duplex mode at distances up to 150 nautical miles.
-
product
Signal Architect Simulator Software
GNSS
The GNSS Signal Architect Simulator Software is ideal for applications requiring: High fidelity simulation of GNSS signals Digital data analysis of GNSS signal effects RF signal generation through digital playback Highly repetitive testing where consistency between test runs is critical Easy to use Graphical User Interface Low initial and support costs
-
product
Development Software Suite
JTAG ProVision
The JTAG ProVision software suite is used to generate boundary-scan tests and in-system programming applications for assembled PCBs and systems. This professional development tool is fully automated and supports the import of design data from over 30 different EDA and CAM systems. Other key data inputs are JTAG device BSDL models and a large, well-maintained model library describing thousands of non-JTAG devices.
-
product
Automated Test Environment
AS5657-ATE
The AS5657 Automated Test Environment (AS5657-ATE) is designed to automate device compliance testing according to the SAE-AS5657 “Test Plan/Procedure for AS5643 IEEE-1394b Interface Requirements for Military and Aerospace Vehicle Applications”. The purpose of this tool is to automate and simplify the task of AS5643 compliance verification and testing, which of course is essential for device compatibility within avionics and aerospace programs.
-
product
Telecom/NEBS Testing
Eurofins E&E North America’s extensive capabilities in telecommunications include testing, compliance assistance & design reviews, application preparation and agency liaison. Eurofins tests products for compliance to U.S., Canadian, and international standards for telecom devices, from NEBS equipment to consumer products such as DSL modems.
-
product
PCI Precision Resistor Card 9-Channel, 1.5Ω To 1.81kΩ
50-297-022
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
UXA Signal Analyzer, 2 Hz to 110 GHz
N9042B
Test the real performance of your millimeter-wave (mmWave) innovations in 5G, satellite, radar, and more with our N9042B UXA X-Series signal analyzer and measurement applications. The N9042B provides the industry's widest analysis bandwidth and deepest dynamic range to help you solve your most difficult mmWave challenges — tight design margins and timelines, complex modulation, and stringent standards.
-
product
RF Signal Generators
The RF signal source mainly acts as a stable local oscillator signal in the test, or generates various types of modulated signals, and the two-tone signal is used for signal excitation, receiving sensitivity testing and other applications. When choosing the RF signal source, the frequency range of the signal output, power requirement size, modulation type, frequency stability, amplitude accuracy and many other factors needs to be considered.
-
product
Development Test for Electric Motors with Power Electronics
Test bench for electric machines and inverters in hybrid applications*Control of mechanical parameters*Verification of electrical properties*Checking the LL characteristics*Short circuit measurement*Recording the performance process*Noise measurement*Temperature measurement
-
product
5G Channel Sounding, Reference Solution
The 5G Channel Sounding, Reference Solution is a combination of hardware, software, and measurement expertise providing the essential components to accelerate 5G sounding research. This reference solution enables researchers and design engineers to use, enhance, or modify the test platform as required to meet specific test application needs including scalable channel count, flexibility to transmit and measure in mmWave frequencies, wide transmit and analysis bandwidths, and real-time data processing.
-
product
USB 2.0 SmartCable For MIL-STD-1553 Test And Simulation
ASC1553
The ASC1553 (AIM SmartCable) USB module offers full function test, simulation, monitoring and recording for MIL-STD-1553B applications implemented in an ultra compact form factor.
-
product
Tensile Test Chambers
Tensile strength tests are an integral part of material development. Materials that require this test include various metals, plastics, paper, fabrics, fibers, composites, and films for many industries. ESPEC tensile test chambers are designed to work with any tension apparatus and can be customized to meet unique application needs.
-
product
Advanced Power System - Dynamic DC Power Supply, 20 V, 50 A, 1000 W
N7951A
The N7900 Series dynamic DC power supplies are designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
product
Digital Reconfigurable I/O Device
The Digital Reconfigurable I/O (RIO) Device features user-programmable FPGA for onboard processing and flexible I/O operation. You have complete control over the synchronization and timing of all signals and operations along with custom onboard decision-making that executes with hardware-timed speed and reliability. You can configure user-defined hardware for a wide variety of applications, such as custom digital DAQ, high-speed waveform generation, sensor simulation, hardware-in-the-loop (HIL) test, custom digital communications protocols, bit error rate testing, and other applications that require precise timing and control.
-
product
Wi-Fi Testing
WiCheck
Alethea Communications Technologies Pvt Ltd
Use Alethea’s Distributed Architecture based WiCheck Solutions to test performance, scale, functionality, stability and interoperability of your Wi-Fi access points and networks using field like scenarios and real applications.
-
product
New GEL Battery CCA Tester
Hangzhou Xun Anda Electrical Co., Ltd.
1. Test application: 12V/6V batteries test and 12V /24V Starting /Charging system test.2. Test battery type: regular liquid, AGM battery, GEL battery.VRLA battery 3. CCA test range: 40~2000CCA (SAE).4. Voltage test range: 1.5-30V.5. Display SOH (state of health), SOC(state of charge).6. Test for multiple battery standards: SAE, DIN, EN, IEC, CA.JIS7. Graphic LCD display with back light, LCD brightness adjustable.8. Multigle language operation: English, Chinese, Germany, French, Spanish.9. Intergrated thermal printer to print test reports.10. Thermal printer paper roll is 58mm width and 7.5m long. 11.test internal resistance
-
product
PXI-6289, 32 AI (18-Bit, 625 kS/s), 4 AO, 48 DIO, PXI Hybrid, Multifunction I/O
779639-01
32 AI (18-Bit, 625 kS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXI‑6289 offers analog I/O, correlated digital I/O, two 32‑bit counter/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
Traction and Induction Motor Test Systems
Crest makes state-of-the art test systems for testing 3-phase AC motors used in traction and other industrial applications.
-
product
PXIe-1095, 18-Slot (5 Hybrid Slots, 11 PXI Express Slots, 1 PXI Express System Timing Slot), Up to 24 GB/s PXI Chassis
785971-01
PXIe, 18-Slot (5 Hybrid Slots, 11 PXI Express Slots, 1 PXI Express System Timing Slot), Up to 24 GB/s PXI Chassis - The PXIe-1095 features a high-bandwidth backplane and up to 82 W of power and cooling in every slot to meet a wide range of high-performance test and measurement application needs. The chassis incorporates two hot-swappable power supplies to improve the mean time to repair (MTTR) of the PXI system; it also offers a Timing and Synchronization option that includes a built-in oven-con...show more -
product
Universal Timer/Counter for PCI
PCI385
The PCI385 Universal Timer Counter PCI card is an ideal solution for automated test and measurement applications. The PCI385 features two timer/counter inputs. Both inputs have a coaxial connector for the input range of +/- 10 V and high-voltage pins for the input range of +/- 300 V. The coupling of the inputs is either AC or DC. The PCI385 provides 6 measurement functions: frequency, high-time, low-time, period, counter and phase measurements.
-
product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1.5Ω to 1.81kΩ
40-251-022
The 40-251-022 is a programmable resistor module with 4 channels which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
